Absolute shaft encoder, magnetic, CAN SAE J1939 WDGA 58A
Synchro flange;
Housing: Ø 58 mm
16/32-bit Single-turn/Multi-turn;
Shaft: Ø 6 mm / Ø 10 mm
- EnDra® Multiturn Technology: maintenance-free and environmentally friendly
- CAN SAE J1939 protocol
- Forward-looking technology with 32 Bit processor
- 2-colour-LED as indicator for operating condition
- High shaft load up to 220 N radial, 120 N axial
65.536 steps/360° (16 bit)
Multi-turn Resolutionup to 32 bit
Advice: Attention: No option AAS = full IP67 version
Shaft length: L: 12 mm
Max. Permissible shaft loading radial: 125 N
Max. Permissible shaft loading axial: 120 N
Shaft length: L: 20 mm
Max. Permissible shaft loading radial: 220 N
Max. Permissible shaft loading axial: 120 N
Current consumption: typ. 50 mA
Power consumption: max. 0.5 W
LED signaling
Demonstration of the LED status signaling
| Description | |
|---|---|
| CB5 | axial, 5-pin, shield connected to encoder housing |
| Description | |
|---|---|
| CC5 | radial, 5-pin, shield connected to encoder housing |
| Description | |
|---|---|
| L1 | radial, shield connected to encoder housing (IP40) |
| (+) Vcc | BN |
| GND | WH |
| CANHigh | GN |
| CANLow | YE |
| CANGND shield | shield |
| Description | |
|---|---|
| L2 | axial, shield connected to encoder housing |
| (+) Vcc | BN |
| GND | WH |
| CANHigh | GN |
| CANLow | YE |
| CANGND shield | shield |
Your desired STEP file is not listed:
Request STEP file here
| Description | |
|---|---|
| L3 | radial, shield connected to encoder housing |
| (+) Vcc | BN |
| GND | WH |
| CANHigh | GN |
| CANLow | YE |
| CANGND shield | shield |
- Absolute encoders with flange Ø 36 mm / Ø 58 mm
- Single-/Multiturn (16/43)
- Ground-breaking technology 32 Bit processor
- Very high shaft loading, IP67
- EnDra® Multiturn technology: No gears, no battery
- QuattroMag® Singleturn technology: High precision +/- 0,0878°
Download (767 KB)
- Incremental and absolute encoders
- Digital shaft copying
- Made in Germany
- Motorfeedback
- Position Measurement Systems
Download (3.58 MB)
for Wachendorff Automation GmbH & Co. KG.
Download (398 KB)
Clamping claw SP-3-00
suitable for incremental encoder WDG 40A, 50B, 58T, WDGI 58A, 58B, 58C, 58D, 58K, 63B, WDGP 36A, WDGP 58A, WDGP 58B and absolute encoder WDGA 36A, WDGA 58A, WDGA 58B.
Mounting bell MG58A
suitable for incremental encoder WDGI 58A and
absolute encoder WDGA 58A.
Bellows coupling BK29
for encoder with shaft Ø 6 mm, 8 mm, 10 mm or 12 mm*.
Max. offset of shafts radial: ± 0,25 mm or ± 0,30 mm*
Torsion spring stiffness: 150 Nm/rad or 130 Nm/rad*
Double loop coupling DSK29
for encoder with shaft Ø 6 mm, 8 mm or 10 mm.
No moving parts, thermally and electrically insulating, smooth running, maintenance-free.
Good resistance to
Gasoline, oil, benzene, toluene, aromatic and non aromatic hydrocarbons, alcohols, glycols, solvents and many chemicals.
Double loop coupling DSK38
for encoder with shaft Ø 6 mm, 8 mm, 10 mm or 12 mm.
No moving parts, thermally and electrically insulating, smooth running, maintenance-free.
Good resistance to
Gasoline, oil, benzene, toluene, aromatic and non aromatic hydrocarbons, alcohols, glycols, solvents and many chemicals.
Double loop coupling DSK48
for encoder with shaft Ø 10 mm, 12 mm or 14 mm.
No moving parts, thermally and electrically insulating, smooth running, maintenance-free.
Good resistance to
Gasoline, oil, benzene, toluene, aromatic and non aromatic hydrocarbons, alcohols, glycols, solvents and many chemicals.
The encoder WDG 58A CAN SAE J1939 can be supplied in a full IP67 version.
Max. RPM: 3500 min'-1
Permitted Shaft-Loading: axial 100 N; radial 110 N
Starting-torque: approx. 4 Ncm at ambient temperature
The encoder WDGA 58A CAN SAE J1939 is also available with fixed 120 Ohm terminating resistor.
The encoder WDGA 58A CAN SAE J1939 shaft: Ø 6 mm is also available with a shortened shaft L = 10 mm.
Here you find a list of our distributors worldwide
print page
up
Contact
Request form
