deenfresitcntr
WDGP 58E

Hollow bore (blind) encoder, magnetic, WDGP 58E,
Housing: Ø 58 mm

Hollow bore blind: Ø 12 mm, Ø 14, Ø 15 mm;
Ø 6, 8, 10 mm with adapter sleeve;
resolution up to 16384 ppr,
Signal shape: square-wave.

Data sheet General technical Data WDGP (PDF 757 kB)
Endhohlwellen-Drehgeber encoder (hollow bore blind) WDGP 58E
Highlights
  • Due to high quality electronics any number of pulses up to 16384
  • Protection class IP67, at shaft input IP65
  • High output frequency up to 1 MHz
  • Reverse polarity protection and short-circuit protection at 4.75 VDC to 32 VDC
Product details
Flange
hollow shaft (blind-bored)
Pulses per revolution PPR
1-16384
Housing
Ø 58 mm
stainless steel
Shaft
Ø 6 mm
Advice: with adapter sleeve
Shaft length: L: 12 mm
Insertion depth min.: 11 mm
Insertion depth max.: 15 mm
Max. Permissible shaft loading radial: 80 N
Max. Permissible shaft loading axial: 50 N
Ø 8 mm
Advice: with adapter sleeve
Shaft length: L: 12 mm
Insertion depth min.: 11 mm
Insertion depth max.: 15 mm
Max. Permissible shaft loading radial: 80 N
Max. Permissible shaft loading axial: 50 N
Ø 10 mm
Advice: with adapter sleeve
Shaft length: L: 12 mm
Insertion depth min.: 11 mm
Insertion depth max.: 15 mm
Max. Permissible shaft loading radial: 80 N
Max. Permissible shaft loading axial: 50 N
Ø 12 mm
Shaft length: L: 12 mm
Insertion depth min.: 11 mm
Insertion depth max.: 15 mm
Max. Permissible shaft loading radial: 80 N
Max. Permissible shaft loading axial: 50 N
Ø 14 mm
Shaft length: L: 12 mm
Insertion depth min.: 11 mm
Insertion depth max.: 15 mm
Max. Permissible shaft loading radial: 80 N
Max. Permissible shaft loading axial: 50 N
Ø 15 mm
Shaft length: L: 12 mm
Insertion depth min.: 11 mm
Insertion depth max.: 15 mm
Max. Permissible shaft loading radial: 80 N
Max. Permissible shaft loading axial: 50 N
Max. operating speed
6000 rpm
Output circuit
HTL
HTL set zero pulse
HTL, inv.
HTL, inv. set zero pulse
TTL
TTL set zero pulse
TTL, RS422 compatible, inv.
TTL, RS422 compatible, inv. set zero pulse
Output frequency
HTL up to 16384 ppr, max. 600 kHz
TTL up to 16384 ppr, max. 1 MHz
Power supply
4,75 VDC up to 32 VDC
Current consumption: typ. 80 mA

Set zero pulse:

Set: SET = +UB for 2 s
Deaktivate: SET = GND

Operating temperature
Connector: -40 °C up to +85 °C, cable: -20 °C up to +80 °C
Protection class
Housing: IP65, IP67; shaft sealed: IP65

Your desired STEP file is not listed:
Request STEP file here

Description ABN inv. poss.
L3 radial, shield connected to encoder housing
Assignments
 L3L3L3L3
CircuitM11, M12M13, M14N11, N12N13, N14
(+) VccBNBNBNBN
GNDWHWHWHWH
AGNGNGNGN
BYEYEYEYE
NGYGYGYGY
SET-PK-PK
A inv.RDRD--
B inv.BKBK--
N inv.VTVT--
Shieldflexflexflexflex

Your desired STEP file is not listed:
Request STEP file here

Description ABN inv. poss.
SC5 radial, 5-pin, Connector connected to encoder housing-
SC8 radial, 8-pin, Connector connected to encoder housing
SC12 radial, 12-pin, Connector connected to encoder housing
Assignments
SC5SC8SC12
 5-pin8-pin12-pin
connector drawing
CircuitN11, N12M11, M12M13, M14
GND313
(+) Vcc121
A434
B246
N558
SET--5
A inv.-69
B inv.-77
N inv.-810
n. c.--2, 11, 12
Shield---
1-16384 PPR
Power supply VDC
4.75 - 32 VDC
Current consumption
typ. 80 mA
Signal shape
square-wave
Output circuit
HTL inverted
Channels
ABN, and inverted signals
Output
push-pull
Load
max. 40 mA / channel
Signal level mA
at 20 mA
Signal level H>
H > Vcc - 2.5 VDC
Signal level L<
L < 0.5 VDC
Output frequency
max. 600 kHz
Circuit protection
inverse-polarity and short-circuit protection
Light reserve warning
no
Power supply VDC
4.75 - 32 VDC
Current consumption
typ. 80 mA
Signal shape
square-wave
Output circuit
TTL, RS422 comp., inverted
Channels
ABN, and inverted signals
Output
push-pull
Load
max. 40 mA / channel
Signal level mA
at 20 mA
Signal level H>
H > 2.5 VDC
Signal level L<
L < 0.5 VDC
Output frequency
max. 1 MHz
Circuit protection
inverse-polarity and short-circuit protection
Light reserve warning
no
Power supply VDC
4.75 - 32 VDC
Current consumption
typ. 80 mA
Signal shape
square-wave
Output circuit
HTL, inv. set zero pulse
Channels
ABN, and inverted signals
Output
push-pull
Load
max. 40 mA / channel
Signal level mA
at 20 mA
Signal level H>
H > Vcc - 2.5 VDC
Signal level L<
L < 0.5 VDC
Output frequency
max. 600 kHz
Circuit protection
inverse-polarity and short-circuit protection
Light reserve warning
no
Power supply VDC
4.75 - 32 VDC
Current consumption
typ. 80 mA
Signal shape
square-wave
Output circuit
TTL, RS422 compatible, inv. set zero pulse
Channels
ABN, and inverted signals
Output
push-pull
Load
max. 40 mA / channel
Signal level mA
at 20 mA
Signal level H>
H > 2.5 VDC
Signal level L<
L < 0.5 VDC
Output frequency
max. 1 MHz
Circuit protection
inverse-polarity and short-circuit protection
Light reserve warning
no
Power supply VDC
4.75 - 32 VDC
Current consumption
typ. 80 mA
Signal shape
square-wave
Output circuit
HTL
Channels
ABN, and inverted signals
Output
push-pull
Load
max. 40 mA / channel
Signal level mA
at 20 mA
Signal level H>
H > Vcc - 2.5 VDC
Signal level L<
L < 0.5 VDC
Output frequency
max. 600 kHz
Circuit protection
inverse-polarity and short-circuit protection
Light reserve warning
no
Power supply VDC
4.75 - 32 VDC
Current consumption
typ. 80 mA
Signal shape
square-wave
Output circuit
TTL
Channels
ABN, and inverted signals
Output
push-pull
Load
max. 40 mA / channel
Signal level mA
at 20 mA
Signal level H>
H > 2.5 VDC
Signal level L<
L < 0.5 VDC
Output frequency
max. 1 MHz
Circuit protection
inverse-polarity and short-circuit protection
Light reserve warning
no
Power supply VDC
4.75 - 32 VDC
Current consumption
typ. 80 mA
Signal shape
square-wave
Output circuit
HTL set zero pulse
Channels
ABN, and inverted signals
Output
push-pull
Load
max. 40 mA / channel
Signal level mA
at 20 mA
Signal level H>
H > Vcc - 2.5 VDC
Signal level L<
L < 0.5 VDC
Output frequency
max. 600 kHz
Circuit protection
inverse-polarity and short-circuit protection
Light reserve warning
no
Power supply VDC
4.75 - 32 VDC
Current consumption
typ. 80 mA
Signal shape
square-wave
Output circuit
TTL set zero pulse
Channels
ABN, and inverted signals
Output
push-pull
Load
max. 40 mA / channel
Signal level mA
at 20 mA
Signal level H>
H > 2.5 VDC
Signal level L<
L < 0.5 VDC
Output frequency
max. 1 MHz
Circuit protection
inverse-polarity and short-circuit protection
Light reserve warning
no
The encoder WDGP 58E can be supplied with more than 2 m cable. The maximum cable length depends on the supply voltage and the frequency; see 'General Technical Data'
Please extend the standard order code with a three figure number, specifying the cable length in decimetres.
Example: 5 m cable = 050
KI567 Drehgeber Kabeldose
KI-5-67

Female connector KI-5-67:
Suitable for encoder with sensor connector outlet SB5 and SC5, 5 pin, IP67

Ready-made shielded connection cable with female cable connector straight,
shield connected.

KIA567 Drehgeber Kabeldose
KIA-5-67

Female connector KIA-5-67:
Suitable for encoder with sensor connector outlet SB5 and SC5, 5 pin, IP67

Ready-made shielded connection cable with female cable connector angular,
shield connected.

KI867 Drehgeber Kabeldose
KI-8-67

Female connector KI-8-67:
Suitable for encoder with sensor connector outlet SB8 and SC8, 8 pin, IP67

Ready-made shielded connection cable with female cable connector straight,
shield connected.

KIA867 Drehgeber Kabeldose
KIA-8-67

Female connector KIA-8-67:
Suitable for encoder with sensor connector outlet SB8 and SC8, 8 pin, IP67

Ready-made shielded connection cable with female cable connector angular,
shield connected.

KI1267 Drehgeber Kabeldose
KI-12-67

Female connector KI-12-67:
Suitable for encoder with sensor connector outlet SB12 and SC12, 12 pin, IP67

Ready-made shielded connection cable with female cable connector straight,
shield connected.

KIA1267 Drehgeber Kabeldose
KIA-12-67

Female connector KIA-12-67:
Suitable for encoder with sensor connector outlet SB12 and SC12, 12 pin, IP67

Ready-made shielded connection cable with female cable connector angular,
shield connected.

WDGDS10001
WDGDS10001

Torque support WDGDS10001

suitable for thru-bore or holllow bore (blind) encodes (all types). Is privieded as standard in the required number with all hollow shaft encoders and end hollow shaft encoders (except WDGA 36E).

WDGDS10003
WDGDS10003

Torque support WDGDS10003

for hollow shaft encoders and end hollow shaft encoders
(all types, except WDGA 36E).

WDGDS10004
WDGDS10004

Torque support WDGDS10004

Torque support for hollow shaft encoders and end hollow shaft encoders
(all types, except WDGA 36E).

WDGDS10007
WDGDS10007

Torque support WDGDS10007

Torque support for hollow shaft encoders and end hollow shaft encoders
(all types, except WDGA 36E).

WDGDS10008
WDGDS10008

Torque support WDGDS10008

for hollow shaft encoders and end hollow shaft encoders
(all types, except WDGA 36E).

WDGDS10009
WDGDS10009

Torque support WDGDS10009

Torque support for hollow shaft encoders and end hollow shaft encoders
(all types, except WDGA 36E).

WDGDS10012
WDGDS10012

Torque support WDGDS10012

for hollow shaft encoders and end hollow shaft encoders
(all types, except WDGA 36E).

WDGDS10019
WDGDS10019

Torque support WDGDS10019

for hollow shaft encoder WDGI 58H, WDGI 58E and WDGA 58E.

Drehmomentstütze WDGDS10020 Torque support
WDGDS10020

Torque support WDGDS10020

Torque support for hollow shaft encoders and end hollow shaft encoders
(all types, except WDGA 36E, WDG 40E, WDG 100G).

WDGDS10005 Drehgeber Kunststoffmitnehmer
WDGDS10005

Plastic dog WDGDS10005

suitable for incremental encoder WDGI 58H, WDGI 58E
and absolute encoders WDGA 58E
(CANopen, CANopen LIFT, CAN SAE J199, SSI, RS485).

WDGWA10M06 Drehgeber encoder Wellenadapter shaft adapter
WDGWA10M06

Shaft adapter WDGWA10M06

for thru-bore and hollow bore (blind) encoder Ø 10 mm
or couplings Ø 10 mm,
thread M6.

WDGWA10M08 Drehgeber Wellenadapter
WDGWA10M08

Shaft adapter WDGWA10M08

for thru-bore and hollow bore (blind) encoder Ø 10 mm
or couplings Ø 10 mm,
thread M8.

WDGWA10M10 Drehgeber Wellenadapter
WDGWA10M10

Shaft adapter WDGWA10M10

for thru-bore and hollow bore (blind) encoder Ø 10 mm
or couplings Ø 10 mm,
thread M10.

WDGWA10M12 Drehgeber Wellenadapter
WDGWA10M12

Shaft adapter WDGWA10M12

for thru-bore and hollow bore (blind) encoder Ø 10 mm
or couplings Ø 10 mm,
thread M12.

WDGWA10M14 Drehgeber Wellenadapter
WDGWA10M14

Shaft adapter WDGWA10M14

for thru-bore and hollow bore (blind) encoder Ø 10 mm
or couplings Ø 10 mm,
thread M14.

WDGWA10M16 Drehgeber Wellenadapter
WDGWA10M16

Shaft adapter WDGWA10M16

for thru-bore and hollow bore (blind) encoder Ø 10 mm
or couplings Ø 10 mm,
thread M16.

WDGWA10M20 Drehgeber Wellenadapter
WDGWA10M20

Shaft adapter WDGWA10M20

for thru-bore and hollow bore (blind) encoder Ø 10 mm
or couplings Ø 10 mm,
thread M20.

WDGHA12XX Reduzierhuelse Drehgeber
WDGHA12

Adpater sleeves for bore size Ø 12 mm

for thru-bore encoder WDGI 58H and
hollow bore (blind) encoder WDGI 58E, WDGA 58E.

Generally encoder specifications

Incremental encoder specifications

Electrical connection

Cable outlet
Connector

Your configured order code

ShaftPPRChannelsOutputConnectionOption
WDGP 58E1-16384ABN
distributors
For further information please contact our local distributor.
Here you find a list of our distributors worldwide
You want to get an offer or want a recall. Request